Menu
GSI – Gesellschaft für Schweißtechnik international mbH
Niederlassung SLV München
Schweißtechnik - WeiterbildungschweißenSchweißtechnik Indrustrie

PT Penetration testing

The penetration test is a widely used test method that is used in almost all industrial sectors. With a few exceptions, all materials can be tested using this method.
Another advantage is the low equipment expense. Depending on the surface, the process can be carried out in color (red-white test) or fluorescently.

Qualification levels

ISO 9712 differentiates between three qualification levels with different areas of responsibility. After authorization by the employer

  • Level 1 personnel can perform the test procedure and record the test results
  • Level 2 personnel can undertake Level 1 activities and evaluate the test results in accordance with standards and regulations
  • Level 3 personnel can undertake Level 2 activities and select the applicable test procedure and process descriptions on which the Level 2 staff can work. Level 3 personnel may take full responsibility for a test facility.

Course contents

The course teaches the physical fundamentals of the test procedure, which are put into practice by means of a large number of practice pieces. The standard-compliant logging and the writing of test instructions are further components of the lesson.

The standardized evaluation of the test results is explained on the basis of the current standards and carried out in practical lessons. Test pieces with known discontinuities allow the control of the evaluation.

Environmental aspects, storage, disposal and the correct transport of test equipment are explained.

Requirements

As an entry requirement for the course, the degree in a metalworking profession is recommended. If you have a degree as an engineer, technician or industrial foreman (technical area), you have the opportunity to take a shortened, 3-day course. Prerequisite for the test is the confirmation of the required visual capacity:

  • The close vision ability must be sufficient to read the Jaeger Number 1 letters or Times New Roman 4.5 or equivalent marks at a distance of not less than 30 cm with at least one eye, with or without visual aid
  • the color vision must be sufficient so that in the particular NDT process the contrast between colors or shades of gray can be recognized and distinguished, as determined by the employer

Furthermore, the employer must confirm an industrial previous experience of at least 10 days. If this previous experience is not available, then this can be acquired by a pre-practical internship in our house.
Certification for level 2 requires at least 4 months' prior industrial experience certified by the employer.

Certification

The qualification test is carried out by the personnel certification body of TÜV NORD. Usually the participant submits a certification application following his examination so that he receives a corresponding certificate. The certificates of TÜV NORD are DAKKS accredited and cover the industrial sector of welded joints when attending a VT 1/2 (w) course or, in the case of a multisectoral course, the industrial sectors "Castings (c)", "Forgings (f)", "welded products (w)","pipes and tubes (t)" and "rolled products (wp)".

Renewal and recertification

After a period of validity of the certificate vor 5 years, a renewal must be requested from the personnel certification body of TÜV NORD. In doing so, the employer must confirm that there has been no significant interruption in the candidate's continued work in the field of visual testing. The renewal is not connected with an exam.
The recertification in Level 2, which is due after another 5 years, is linked to a practical exam, the recertification exam. In the recertification exam, selected test pieces must be tested, the test results recorded and a test instruction has to be created. Usually, the candidate will pre-enroll in a recertification course in order to become familiar with the possibly revised regulations and the preparation of the test instructions.

 

Company courses

For groups of five or more participants, we are also happy to offer you our training courses in your company. In such in-house trainings, we can target your products and special requirements. We take care of test pieces and test equipment. Please organize a room for the theoretical lessons and maybe a separate room for the practical exercises.

We are happy to prepare an offer for your tailored further training.

Contact person

SLV München


Do you have questions?

Contact us!

SEND AN E-MAIL!